[Freeswitch-users] TDM400 FXO can dialout only once
Anthony Minessale
anthony.minessale at gmail.com
Sun Jan 25 18:18:54 PST 2009
Its not detecting a dial tone on the failure case.
Before dialing it waits until it picks up dialtone.
Try the svn trunk version to see if it works any better or verify there is a
dialtone on the line.
On Jan 25, 2009 6:19 PM, "Nandy Dagondon" <gcd at i.ph> wrote:
hi everybody,
i installed FS 1.0.2 to an Atom mobo (Intel D945GCLF2). it's working using
IP phones, softphones and digium FXS port. but there's a problem in dialing
out to PSTN using digium tdm400 fxo - it works fine on the first attempt
(after starting FS) but it fails on the subsequent attempts. i tested to
call using the FXS port and IP phone. same problem.
before i place any call, i checked >oz dump 2 1 (show current state = DOWN,
last state = DOWN)
in the first call, there's this message:
[WARNING] mod_openzap.c:1196 on_fxo_signal() Unhandled type for channel 2:1
but
then i hangup. checked >oz dump 21 (show current state=DOWN, last
state=HANGUP)
in the 2nd (and subsequent) attempts, the fxo just goes off-hook but doesn't
send the dtmf tones.
>oz dump 2 1 (shows current state = DIALING, last state = DOWN)
has anyone encountered this problem before? i appreciate for any help to
correct this problem.
tks,
nandy
Environment:
==================
kernel 2.6.18-92.1.22.el5
FS 1.0.2
zaptel 1.4.11
oslec
digium TDM400P Rev. I (1-FXS, 2-FXO,3-4 vacant)
zaptel.conf
========
loadzone = us
defaultzone=us
channels=1-2
alaw=1-4
fxsks=2
fxoks=1
openzap.conf.xml:
===============
<configuration name="openzap.conf" description="OpenZAP Configuration">
<settings>
<param name="debug" value="9"/>
<!-- <param name="hold-music" value="$${moh_uri}"/> -->
<!-- <param name="enable-analog-option" value="call-swap"/> -->
<!-- <param name="enable-analog-option" value="3-way"/> -->
</settings>
<!-- one entry here per openzap span -->
<analog_spans>
<span id="1">
<!--<param name="hold-music" value="$${moh_uri}"/>-->
<!--<param name="enable-analog-option" value="call-swap"/>-->
<!--<param name="enable-analog-option" value="3-way"/>-->
<param name="tonegroup" value="us"/>
<param name="digit-timeout" value="2000"/>
<param name="max-digits" value="15"/>
<param name="dialplan" value="XML"/>
<param name="context" value="default"/>
<param name="enable-callerid" value="false"/>
<!-- regex to stop dialing when it matches -->
<!--<param name="dial-regex" value="5555"/>-->
<!-- regex to stop dialing when it does not match -->
<!--<param name="fail-dial-regex" value="^5"/>-->
</span>
<span id="2">
<!--<param name="hold-music" value="$${moh_uri}"/>-->
<!--<param name="enable-analog-option" value="call-swap"/>-->
<!--<param name="enable-analog-option" value="3-way"/>-->
<param name="tonegroup" value="us"/>
<param name="digit-timeout" value="2000"/>
<param name="max-digits" value="11"/>
<param name="dialplan" value="XML"/>
<param name="context" value="default"/>
<param name="enable-callerid" value=""false/>
<!-- regex to stop dialing when it matches -->
<!--<param name="dial-regex" value="5555"/>-->
<!-- regex to stop dialing when it does not match -->
<!--<param name="fail-dial-regex" value="^5"/>-->
</span>
</analog_spans>
</configuration>
openzap.conf
==========
[span zt]
name => OpenZAP FXS
number => 1
fxs-channel => 1
[span zt]
name => OpenZAP FXO
number => 2
fxo-channel => 2
tones.conf (the dialtone and ring tone is set to Philipping tones)
========
[us]
generate-dial => v=-7;%(1000,0,425)
detect-dial => 425
generate-ring => v=-7;%(1000,4000,425,480)
detect-ring => 425,480
generate-busy => v=-7;%(500,500,480,620)
detect-busy => 480,620
generate-attn => v=0;%(200,300,1400,1800)
detect-attn => 1400,1800
generate-callwaiting-sas => v=0;%(300,10000,440)
detect-callwaiting-sas => 440
generate-callwaiting-cas => v=0;%(80,0,2750,2130)
detect-callwaiting-cas => 2750,2130
detect-fail1 => 913.8
detect-fail2 => 1370.6
detect-fail3 => 776.7
LOG OF FIRST CALL (OK)
====================
2009-01-25 10:35:58 [DEBUG] switch_core_state_machine.c:152
switch_core_standard_on_execute() OpenZAP/1:1/93400534 Execute
bridge(openzap/2/1/3400534)
2009-01-25 10:35:58 [DEBUG] mod_openzap.c:340 tech_init() Set codec PCMU
20ms
2009-01-25 10:35:58 [DEBUG] mod_openzap.c:1017 channel_outgoing_channel()
Connect outbound channel OpenZAP/2:1/3400534
2009-01-25 10:35:58 [NOTICE] switch_channel.c:565 switch_channel_set_name()
New Channel OpenZAP/2:1/3400534 [e5f12114-ea88-11dd-9f5c-290fb4a527a4]
2009-01-25 10:35:58 [DEBUG] mod_openzap.c:1026 channel_outgoing_channel()
(OpenZAP/2:1/3400534) State Change CS_NEW -> CS_INIT
2009-01-25 10:35:58 [DEBUG] switch_core_session.c:807
switch_core_session_signal_state_change() Send signal OpenZAP/2:1/3400534
[BREAK]
2009-01-25 10:35:58 [DEBUG] ozmod_analog.c:52 analog_fxo_outgoing_call()
Changing state on 2:1 from DOWN to DIALING
2009-01-25 10:35:58 [DEBUG] ozmod_analog.c:239 zap_analog_channel_run()
ANALOG CHANNEL thread starting.
2009-01-25 10:35:58 [DEBUG] switch_core_state_machine.c:379
switch_core_session_run() (OpenZAP/2:1/3400534) Running State Change CS_INIT
2009-01-25 10:35:58 [DEBUG] ozmod_analog.c:410 zap_analog_channel_run()
Executing state handler on 2:1 for DIALING
2009-01-25 10:35:58 [DEBUG] switch_core_state_machine.c:444
switch_core_session_run() (OpenZAP/2:1/3400534) State INIT
2009-01-25 10:35:58 [DEBUG] mod_openzap.c:364 channel_on_init()
(OpenZAP/2:1/3400534) State Change CS_INIT -> CS_ROUTING
2009-01-25 10:35:58 [DEBUG] switch_core_session.c:807
switch_core_session_signal_state_change() Send signal OpenZAP/2:1/3400534
[BREAK]
2009-01-25 10:35:58 [DEBUG] switch_core_state_machine.c:444
switch_core_session_run() (OpenZAP/2:1/3400534) State INIT going to sleep
2009-01-25 10:35:58 [DEBUG] switch_core_state_machine.c:379
switch_core_session_run() (OpenZAP/2:1/3400534) Running State Change
CS_ROUTING
2009-01-25 10:35:58 [DEBUG] switch_core_state_machine.c:447
switch_core_session_run() (OpenZAP/2:1/3400534) State ROUTING
2009-01-25 10:35:58 [DEBUG] mod_openzap.c:387 channel_on_routing()
OpenZAP/2:1/3400534 CHANNEL ROUTING
2009-01-25 10:35:58 [DEBUG] switch_ivr_originate.c:58 originate_on_routing()
(OpenZAP/2:1/3400534) State Change CS_ROUTING -> CS_CONSUME_MEDIA
2009-01-25 10:35:58 [DEBUG] switch_core_session.c:807
switch_core_session_signal_state_change() Send signal OpenZAP/2:1/3400534
[BREAK]
2009-01-25 10:35:58 [DEBUG] switch_core_state_machine.c:447
switch_core_session_run() (OpenZAP/2:1/3400534) State ROUTING going to sleep
2009-01-25 10:35:58 [DEBUG] switch_core_state_machine.c:379
switch_core_session_run() (OpenZAP/2:1/3400534) Running State Change
CS_CONSUME_MEDIA
2009-01-25 10:35:58 [DEBUG] switch_core_state_machine.c:466
switch_core_session_run() (OpenZAP/2:1/3400534) State CONSUME_MEDIA
2009-01-25 10:35:59 [DEBUG] ozmod_analog.c:615 zap_analog_channel_run()
Detected tone DIAL on 2:1
2009-01-25 10:35:59 [DEBUG] mod_openzap.c:1153 on_fxo_signal() got FXO sig
2:1 [TONE_DETECTED]
2009-01-25 10:35:59 [WARNING] mod_openzap.c:1196 on_fxo_signal() Unhandled
type for channel 2:1
2009-01-25 10:35:59 [DEBUG] zap_io.c:1179 zchan_activate_dtmf_buffer()
Created DTMF Buffer!
2009-01-25 10:35:59 [DEBUG] zap_io.c:1715 handle_dtmf() 2:1 GENERATE DTMF
[3400534]
2009-01-25 10:36:03 [DEBUG] ozmod_analog.c:302 zap_analog_channel_run()
Changing state on 2:1 from DIALING to UP
2009-01-25 10:36:03 [DEBUG] ozmod_analog.c:410 zap_analog_channel_run()
Executing state handler on 2:1 for UP
2009-01-25 10:36:03 [DEBUG] mod_openzap.c:1153 on_fxo_signal() got FXO sig
2:1 [UP]
2009-01-25 10:36:03 [DEBUG] switch_channel.c:1710
switch_channel_perform_mark_answered() Send signal OpenZAP/1:1/93400534
[BREAK]
2009-01-25 10:36:03 [NOTICE] mod_openzap.c:1180 on_fxo_signal() Channel
[OpenZAP/2:1/3400534] has been answered
2009-01-25 10:36:03 [DEBUG] switch_channel.c:177 switch_channel_audio_sync()
OpenZAP/2:1/3400534 receive message [AUDIO_SYNC]
2009-01-25 10:36:03 [DEBUG] switch_channel.c:1768
switch_channel_perform_answer() OpenZAP/1:1/93400534 receive message
[ANSWER]
2009-01-25 10:36:03 [DEBUG] mod_openzap.c:813 channel_receive_message_fxs()
Changing state on 1:1 from IDLE to UP
2009-01-25 10:36:03 [NOTICE] mod_openzap.c:814 channel_receive_message_fxs()
Channel [OpenZAP/1:1/93400534] has been answered
2009-01-25 10:36:03 [DEBUG] switch_channel.c:177 switch_channel_audio_sync()
OpenZAP/1:1/93400534 receive message [AUDIO_SYNC]
2009-01-25 10:36:03 [DEBUG] switch_core_session.c:511
switch_core_session_perform_receive_message() Send signal
OpenZAP/1:1/93400534 [BREAK]
2009-01-25 10:36:03 [DEBUG] switch_ivr_originate.c:1627
switch_ivr_originate() Originate Resulted in Success: [OpenZAP/2:1/3400534]
2009-01-25 10:36:03 [DEBUG] switch_channel.c:177 switch_channel_audio_sync()
OpenZAP/2:1/3400534 receive message [AUDIO_SYNC]
2009-01-25 10:36:03 [DEBUG] switch_channel.c:177 switch_channel_audio_sync()
OpenZAP/1:1/93400534 receive message [AUDIO_SYNC]
2009-01-25 10:36:03 [DEBUG] switch_ivr_bridge.c:862
switch_ivr_multi_threaded_bridge() OpenZAP/2:1/3400534 receive message
[BRIDGE]
2009-01-25 10:36:03 [DEBUG] switch_core_session.c:511
switch_core_session_perform_receive_message() Send signal
OpenZAP/2:1/3400534 [BREAK]
2009-01-25 10:36:03 [DEBUG] switch_ivr_bridge.c:869
switch_ivr_multi_threaded_bridge() OpenZAP/1:1/93400534 receive message
[BRIDGE]
2009-01-25 10:36:03 [DEBUG] switch_core_session.c:511
switch_core_session_perform_receive_message() Send signal
OpenZAP/1:1/93400534 [BREAK]
2009-01-25 10:36:03 [DEBUG] switch_ivr_bridge.c:913
switch_ivr_multi_threaded_bridge() (OpenZAP/2:1/3400534) State Change
CS_CONSUME_MEDIA -> CS_EXCHANGE_MEDIA
2009-01-25 10:36:03 [DEBUG] switch_core_session.c:807
switch_core_session_signal_state_change() Send signal OpenZAP/2:1/3400534
[BREAK]
2009-01-25 10:36:03 [DEBUG] ozmod_analog.c:410 zap_analog_channel_run()
Executing state handler on 1:1 for UP
2009-01-25 10:36:03 [DEBUG] mod_openzap.c:1212 on_fxs_signal() got FXS sig
[UP]
2009-01-25 10:36:03 [DEBUG] switch_core_state_machine.c:466
switch_core_session_run() (OpenZAP/2:1/3400534) State CONSUME_MEDIA going to
sleep
2009-01-25 10:36:03 [DEBUG] switch_core_state_machine.c:379
switch_core_session_run() (OpenZAP/2:1/3400534) Running State Change
CS_EXCHANGE_MEDIA
2009-01-25 10:36:03 [DEBUG] switch_core_state_machine.c:457
switch_core_session_run() (OpenZAP/2:1/3400534) State EXCHANGE_MEDIA
2009-01-25 10:36:03 [DEBUG] mod_openzap.c:511 channel_on_exchange_media()
CHANNEL EXCHANGE_MEDIA
2009-01-25 10:36:16 [DEBUG] ozmod_analog.c:744 process_event() EVENT
[ONHOOK][1:1] STATE [UP]
2009-01-25 10:36:16 [DEBUG] ozmod_analog.c:780 process_event() Changing
state on 1:1 from UP to DOWN
2009-01-25 10:36:16 [DEBUG] ozmod_analog.c:410 zap_analog_channel_run()
Executing state handler on 1:1 for DOWN
2009-01-25 10:36:16 [DEBUG] mod_openzap.c:1212 on_fxs_signal() got FXS sig
[STOP]
2009-01-25 10:36:16 [NOTICE] mod_openzap.c:1300 on_fxs_signal() Hangup
OpenZAP/1:1/93400534 [CS_EXECUTE] [NORMAL_CLEARING]
2009-01-25 10:36:16 [DEBUG] switch_channel.c:1494
switch_channel_perform_hangup() Send signal OpenZAP/1:1/93400534 [KILL]
2009-01-25 10:36:16 [DEBUG] switch_core_session.c:807
switch_core_session_signal_state_change() Send signal OpenZAP/1:1/93400534
[BREAK]
2009-01-25 10:36:16 [DEBUG] zap_io.c:1125 zap_channel_done() channel done
1:1
2009-01-25 10:36:16 [DEBUG] ozmod_analog.c:726 zap_analog_channel_run()
ANALOG CHANNEL 1:1 thread ended.
2009-01-25 10:36:16 [DEBUG] switch_ivr_bridge.c:360 audio_bridge_thread()
OpenZAP/1:1/93400534 ending bridge by request from read function
2009-01-25 10:36:16 [DEBUG] switch_ivr_bridge.c:435 audio_bridge_thread()
BRIDGE THREAD DONE [OpenZAP/1:1/93400534]
2009-01-25 10:36:16 [DEBUG] switch_ivr_bridge.c:439 audio_bridge_thread()
Send signal OpenZAP/2:1/3400534 [BREAK]
2009-01-25 10:36:16 [DEBUG] switch_ivr_bridge.c:354 audio_bridge_thread()
OpenZAP/1:1/93400534 ending bridge by request from write function
2009-01-25 10:36:16 [DEBUG] switch_ivr_bridge.c:409 audio_bridge_thread()
OpenZAP/2:1/3400534 receive message [UNBRIDGE]
2009-01-25 10:36:16 [DEBUG] switch_core_session.c:511
switch_core_session_perform_receive_message() Send signal
OpenZAP/2:1/3400534 [BREAK]
2009-01-25 10:36:16 [DEBUG] switch_ivr_bridge.c:435 audio_bridge_thread()
BRIDGE THREAD DONE [OpenZAP/2:1/3400534]
2009-01-25 10:36:16 [DEBUG] switch_ivr_bridge.c:439 audio_bridge_thread()
Send signal OpenZAP/1:1/93400534 [BREAK]
2009-01-25 10:36:16 [NOTICE] switch_ivr_bridge.c:470
audio_bridge_on_exchange_media() Hangup OpenZAP/2:1/3400534
[CS_EXCHANGE_MEDIA] [NORMAL_CLEARING]
2009-01-25 10:36:16 [DEBUG] switch_channel.c:1494
switch_channel_perform_hangup() Send signal OpenZAP/2:1/3400534 [KILL]
2009-01-25 10:36:16 [DEBUG] switch_core_session.c:807
switch_core_session_signal_state_change() Send signal OpenZAP/2:1/3400534
[BREAK]
2009-01-25 10:36:16 [DEBUG] switch_core_state_machine.c:457
switch_core_session_run() (OpenZAP/2:1/3400534) State EXCHANGE_MEDIA going
to sleep
2009-01-25 10:36:16 [DEBUG] switch_core_state_machine.c:379
switch_core_session_run() (OpenZAP/2:1/3400534) Running State Change
CS_HANGUP
2009-01-25 10:36:16 [DEBUG] switch_core_state_machine.c:410
switch_core_session_run() (OpenZAP/2:1/3400534) State HANGUP
2009-01-25 10:36:16 [DEBUG] mod_openzap.c:429 channel_on_hangup() Changing
state on 2:1 from UP to HANGUP
2009-01-25 10:36:16 [DEBUG] mod_openzap.c:472 channel_on_hangup()
OpenZAP/2:1/3400534 CHANNEL HANGUP
2009-01-25 10:36:16 [DEBUG] switch_core_state_machine.c:46
switch_core_standard_on_hangup() OpenZAP/2:1/3400534 Standard HANGUP, cause:
NORMAL_CLEARING
2009-01-25 10:36:16 [DEBUG] switch_core_state_machine.c:410
switch_core_session_run() (OpenZAP/2:1/3400534) State HANGUP going to sleep
2009-01-25 10:36:16 [DEBUG] switch_core_session.c:939
switch_core_session_thread() Session 2 (OpenZAP/2:1/3400534) Locked, Waiting
on external entities
2009-01-25 10:36:16 [DEBUG] switch_core_state_machine.c:454
switch_core_session_run() (OpenZAP/1:1/93400534) State EXECUTE going to
sleep
2009-01-25 10:36:16 [NOTICE] switch_core_session.c:957
switch_core_session_thread() Session 2 (OpenZAP/2:1/3400534) Ended
2009-01-25 10:36:16 [NOTICE] switch_core_session.c:959
switch_core_session_thread() Close Channel OpenZAP/2:1/3400534 [CS_HANGUP]
2009-01-25 10:36:16 [DEBUG] switch_core_state_machine.c:379
switch_core_session_run() (OpenZAP/1:1/93400534) Running State Change
CS_HANGUP
2009-01-25 10:36:16 [DEBUG] switch_core_state_machine.c:410
switch_core_session_run() (OpenZAP/1:1/93400534) State HANGUP
2009-01-25 10:36:16 [DEBUG] mod_openzap.c:472 channel_on_hangup()
OpenZAP/1:1/93400534 CHANNEL HANGUP
2009-01-25 10:36:16 [DEBUG] switch_core_state_machine.c:46
switch_core_standard_on_hangup() OpenZAP/1:1/93400534 Standard HANGUP,
cause: NORMAL_CLEARING
2009-01-25 10:36:16 [DEBUG] switch_core_state_machine.c:410
switch_core_session_run() (OpenZAP/1:1/93400534) State HANGUP going to sleep
2009-01-25 10:36:16 [DEBUG] switch_core_session.c:939
switch_core_session_thread() Session 1 (OpenZAP/1:1/93400534) Locked,
Waiting on external entities
2009-01-25 10:36:16 [NOTICE] switch_core_session.c:957
switch_core_session_thread() Session 1 (OpenZAP/1:1/93400534) Ended
2009-01-25 10:36:16 [NOTICE] switch_core_session.c:959
switch_core_session_thread() Close Channel OpenZAP/1:1/93400534 [CS_HANGUP]
2009-01-25 10:36:16 [DEBUG] ozmod_analog.c:410 zap_analog_channel_run()
Executing state handler on 2:1 for HANGUP
2009-01-25 10:36:17 [DEBUG] ozmod_analog.c:351 zap_analog_channel_run()
Changing state on 2:1 from HANGUP to DOWN
2009-01-25 10:36:17 [DEBUG] ozmod_analog.c:410 zap_analog_channel_run()
Executing state handler on 2:1 for DOWN
2009-01-25 10:36:17 [DEBUG] mod_openzap.c:1153 on_fxo_signal() got FXO sig
2:1 [STOP]
2009-01-25 10:36:17 [DEBUG] zap_io.c:1125 zap_channel_done() channel done
2:1
2009-01-25 10:36:17 [DEBUG] ozmod_analog.c:726 zap_analog_channel_run()
ANALOG CHANNEL 2:1 thread ended.
LOG OF FAILED CALLS
==================
2009-01-25 10:36:55 [DEBUG] switch_core_state_machine.c:152
switch_core_standard_on_execute() OpenZAP/1:1/93400534 Execute
bridge(openzap/2/1/3400534)
2009-01-25 10:36:55 [DEBUG] mod_openzap.c:340 tech_init() Set codec PCMU
20ms
2009-01-25 10:36:55 [DEBUG] mod_openzap.c:1017 channel_outgoing_channel()
Connect outbound channel OpenZAP/2:1/3400534
2009-01-25 10:36:55 [NOTICE] switch_channel.c:565 switch_channel_set_name()
New Channel OpenZAP/2:1/3400534 [079f5420-ea89-11dd-9f5c-290fb4a527a4]
2009-01-25 10:36:55 [DEBUG] mod_openzap.c:1026 channel_outgoing_channel()
(OpenZAP/2:1/3400534) State Change CS_NEW -> CS_INIT
2009-01-25 10:36:55 [DEBUG] switch_core_session.c:807
switch_core_session_signal_state_change() Send signal OpenZAP/2:1/3400534
[BREAK]
2009-01-25 10:36:55 [DEBUG] ozmod_analog.c:52 analog_fxo_outgoing_call()
Changing state on 2:1 from DOWN to DIALING
2009-01-25 10:36:55 [DEBUG] ozmod_analog.c:239 zap_analog_channel_run()
ANALOG CHANNEL thread starting.
2009-01-25 10:36:55 [DEBUG] switch_core_state_machine.c:379
switch_core_session_run() (OpenZAP/2:1/3400534) Running State Change CS_INIT
2009-01-25 10:36:55 [DEBUG] ozmod_analog.c:410 zap_analog_channel_run()
Executing state handler on 2:1 for DIALING
2009-01-25 10:36:55 [DEBUG] switch_core_state_machine.c:444
switch_core_session_run() (OpenZAP/2:1/3400534) State INIT
2009-01-25 10:36:55 [DEBUG] mod_openzap.c:364 channel_on_init()
(OpenZAP/2:1/3400534) State Change CS_INIT -> CS_ROUTING
2009-01-25 10:36:55 [DEBUG] switch_core_session.c:807
switch_core_session_signal_state_change() Send signal OpenZAP/2:1/3400534
[BREAK]
2009-01-25 10:36:55 [DEBUG] switch_core_state_machine.c:444
switch_core_session_run() (OpenZAP/2:1/3400534) State INIT going to sleep
2009-01-25 10:36:55 [DEBUG] switch_core_state_machine.c:379
switch_core_session_run() (OpenZAP/2:1/3400534) Running State Change
CS_ROUTING
2009-01-25 10:36:55 [DEBUG] switch_core_state_machine.c:447
switch_core_session_run() (OpenZAP/2:1/3400534) State ROUTING
2009-01-25 10:36:55 [DEBUG] mod_openzap.c:387 channel_on_routing()
OpenZAP/2:1/3400534 CHANNEL ROUTING
2009-01-25 10:36:55 [DEBUG] switch_ivr_originate.c:58 originate_on_routing()
(OpenZAP/2:1/3400534) State Change CS_ROUTING -> CS_CONSUME_MEDIA
2009-01-25 10:36:55 [DEBUG] switch_core_session.c:807
switch_core_session_signal_state_change() Send signal OpenZAP/2:1/3400534
[BREAK]
2009-01-25 10:36:55 [DEBUG] switch_core_state_machine.c:447
switch_core_session_run() (OpenZAP/2:1/3400534) State ROUTING going to sleep
2009-01-25 10:36:55 [DEBUG] switch_core_state_machine.c:379
switch_core_session_run() (OpenZAP/2:1/3400534) Running State Change
CS_CONSUME_MEDIA
2009-01-25 10:36:55 [DEBUG] switch_core_state_machine.c:466
switch_core_session_run() (OpenZAP/2:1/3400534) State CONSUME_MEDIA
2009-01-25 10:37:08 [DEBUG] ozmod_analog.c:744 process_event() EVENT
[ONHOOK][1:1] STATE [IDLE]
2009-01-25 10:37:08 [DEBUG] ozmod_analog.c:780 process_event() Changing
state on 1:1 from IDLE to DOWN
2009-01-25 10:37:08 [DEBUG] ozmod_analog.c:410 zap_analog_channel_run()
Executing state handler on 1:1 for DOWN
2009-01-25 10:37:08 [DEBUG] mod_openzap.c:1212 on_fxs_signal() got FXS sig
[STOP]
2009-01-25 10:37:08 [NOTICE] mod_openzap.c:1300 on_fxs_signal() Hangup
OpenZAP/1:1/93400534 [CS_EXECUTE] [NORMAL_CLEARING]
2009-01-25 10:37:08 [DEBUG] switch_channel.c:1494
switch_channel_perform_hangup() Send signal OpenZAP/1:1/93400534 [KILL]
2009-01-25 10:37:08 [DEBUG] switch_core_session.c:807
switch_core_session_signal_state_change() Send signal OpenZAP/1:1/93400534
[BREAK]
2009-01-25 10:37:08 [DEBUG] zap_io.c:1125 zap_channel_done() channel done
1:1
2009-01-25 10:37:08 [DEBUG] ozmod_analog.c:726 zap_analog_channel_run()
ANALOG CHANNEL 1:1 thread ended.
2009-01-25 10:37:08 [NOTICE] switch_ivr_originate.c:1566
switch_ivr_originate() Hangup OpenZAP/2:1/3400534 [CS_CONSUME_MEDIA]
[ORIGINATOR_CANCEL]
2009-01-25 10:37:08 [DEBUG] switch_channel.c:1494
switch_channel_perform_hangup() Send signal OpenZAP/2:1/3400534 [KILL]
2009-01-25 10:37:08 [DEBUG] switch_core_session.c:807
switch_core_session_signal_state_change() Send signal OpenZAP/2:1/3400534
[BREAK]
2009-01-25 10:37:08 [DEBUG] switch_ivr_originate.c:1691
switch_ivr_originate() Originate Cancelled by originator termination Cause:
487 [ORIGINATOR_CANCEL]
2009-01-25 10:37:08 [INFO] mod_dptools.c:1909 audio_bridge_function()
Originate Failed. Cause: ORIGINATOR_CANCEL
2009-01-25 10:37:08 [DEBUG] switch_core_state_machine.c:454
switch_core_session_run() (OpenZAP/1:1/93400534) State EXECUTE going to
sleep
2009-01-25 10:37:08 [DEBUG] switch_core_state_machine.c:379
switch_core_session_run() (OpenZAP/1:1/93400534) Running State Change
CS_HANGUP
2009-01-25 10:37:08 [DEBUG] switch_core_state_machine.c:410
switch_core_session_run() (OpenZAP/1:1/93400534) State HANGUP
2009-01-25 10:37:08 [DEBUG] mod_openzap.c:472 channel_on_hangup()
OpenZAP/1:1/93400534 CHANNEL HANGUP
2009-01-25 10:37:08 [DEBUG] switch_core_state_machine.c:46
switch_core_standard_on_hangup() OpenZAP/1:1/93400534 Standard HANGUP,
cause: NORMAL_CLEARING
2009-01-25 10:37:08 [DEBUG] switch_core_state_machine.c:410
switch_core_session_run() (OpenZAP/1:1/93400534) State HANGUP going to sleep
2009-01-25 10:37:08 [DEBUG] switch_core_session.c:939
switch_core_session_thread() Session 3 (OpenZAP/1:1/93400534) Locked,
Waiting on external entities
2009-01-25 10:37:08 [NOTICE] switch_core_session.c:957
switch_core_session_thread() Session 3 (OpenZAP/1:1/93400534) Ended
2009-01-25 10:37:08 [DEBUG] switch_core_state_machine.c:466
switch_core_session_run() (OpenZAP/2:1/3400534) State CONSUME_MEDIA going to
sleep
2009-01-25 10:37:08 [NOTICE] switch_core_session.c:959
switch_core_session_thread() Close Channel OpenZAP/1:1/93400534 [CS_HANGUP]
2009-01-25 10:37:08 [DEBUG] switch_core_state_machine.c:379
switch_core_session_run() (OpenZAP/2:1/3400534) Running State Change
CS_HANGUP
2009-01-25 10:37:08 [DEBUG] switch_core_state_machine.c:410
switch_core_session_run() (OpenZAP/2:1/3400534) State HANGUP
2009-01-25 10:37:08 [DEBUG] mod_openzap.c:429 channel_on_hangup() Changing
state on 2:1 from DIALING to HANGUP
2009-01-25 10:37:08 [DEBUG] mod_openzap.c:472 channel_on_hangup()
OpenZAP/2:1/3400534 CHANNEL HANGUP
2009-01-25 10:37:08 [DEBUG] switch_core_state_machine.c:46
switch_core_standard_on_hangup() OpenZAP/2:1/3400534 Standard HANGUP, cause:
ORIGINATOR_CANCEL
2009-01-25 10:37:08 [DEBUG] switch_core_state_machine.c:410
switch_core_session_run() (OpenZAP/2:1/3400534) State HANGUP going to sleep
2009-01-25 10:37:08 [DEBUG] switch_core_session.c:939
switch_core_session_thread() Session 4 (OpenZAP/2:1/3400534) Locked, Waiting
on external entities
2009-01-25 10:37:08 [NOTICE] switch_core_session.c:957
switch_core_session_thread() Session 4 (OpenZAP/2:1/3400534) Ended
2009-01-25 10:37:08 [NOTICE] switch_core_session.c:959
switch_core_session_thread() Close Channel OpenZAP/2:1/3400534 [CS_HANGUP]
2009-01-25 10:37:08 [DEBUG] ozmod_analog.c:410 zap_analog_channel_run()
Executing state handler on 2:1 for HANGUP
2009-01-25 10:37:09 [DEBUG] ozmod_analog.c:351 zap_analog_channel_run()
Changing state on 2:1 from HANGUP to DOWN
2009-01-25 10:37:09 [DEBUG] ozmod_analog.c:410 zap_analog_channel_run()
Executing state handler on 2:1 for DOWN
2009-01-25 10:37:09 [DEBUG] mod_openzap.c:1153 on_fxo_signal() got FXO sig
2:1 [STOP]
2009-01-25 10:37:09 [DEBUG] zap_io.c:1125 zap_channel_done() channel done
2:1
2009-01-25 10:37:09 [DEBUG] ozmod_analog.c:726 zap_analog_channel_run()
ANALOG CHANNEL 2:1 thread ended.
_______________________________________________
Freeswitch-users mailing list
Freeswitch-users at lists.freeswitch.org
http://lists.freeswitch.org/mailman/listinfo/freeswitch-users
UNSUBSCRIBE:http://lists.freeswitch.org/mailman/options/freeswitch-users
http://www.freeswitch.org
-------------- next part --------------
An HTML attachment was scrubbed...
URL: http://lists.freeswitch.org/pipermail/freeswitch-users/attachments/20090125/f284c069/attachment-0002.html
More information about the FreeSWITCH-users
mailing list