[Freeswitch-users] config help: openzap and T1 A102u

Evgeniy Zolotov zolotov at altron.ua
Fri Dec 12 01:00:01 PST 2008 

  Did you try ./wanrouter start before starting FreeSWITCH ?
----- Original Message ----- 
From: <dalechase at yahoo.com>
To: <freeswitch-users at lists.freeswitch.org>
Sent: Friday, December 12, 2008 2:51 AM
Subject: [Freeswitch-users] config help: openzap and T1 A102u


>I am stuck trying to bring up freeswitch with openzap on a Sangoma A102u T1 
>card.
> Works fine with asterisk.
>
> Please point out where I am failing to configure properly.
>
> Running Linux version 2.6.9-34.ELsmp on a Dell Celeron
>
> % wanrouter hwprobe verbose
>
> -----------------------------------------
> | Wanpipe Hardware Probe Info (verbose) |
> -----------------------------------------
> 1 . AFT-A102u  : SLOT=1 : BUS=2 : IRQ=145 : CPU=A : PORT=PRI : V=25
> +01:PMC4351:PCI
> 2 . AFT-A102u  : SLOT=1 : BUS=2 : IRQ=145 : CPU=B : PORT=PRI : V=25
> +01:PMC4351:PCI
>
> Card Cnt: S508=0  S514X=0  S518=0  A101-2=1  A104=0  A300=0  A200=0 
> A108=0
>
> % cat /usr/local/freeswitch/conf/autoload_configs/open
> openmrcp.conf.xml  openzap.conf.xml
> [root at pbxtra1466 freeswitch]# cat 
> /usr/local/freeswitch/conf/autoload_configs/openzap.conf.xml
> <configuration name="openzap.conf" description="OpenZAP Configuration">
>  <settings>
>    <param name="debug" value="0"/>
>    <!--<param name="hold-music" value="$${moh_uri}"/>-->
>    <!--<param name="enable-analog-option" value="call-swap"/>-->
>    <!--<param name="enable-analog-option" value="3-way"/>-->
>  </settings>
>  <!-- one entry here per openzap span -->
>  <analog_spans>
>    <span id="1">
>      <!--<param name="hold-music" value="$${moh_uri}"/>-->
>      <!--<param name="enable-analog-option" value="call-swap"/>-->
>      <!--<param name="enable-analog-option" value="3-way"/>-->
>      <param name="tonegroup" value="us"/>
>      <param name="digit-timeout" value="2000"/>
>      <param name="max-digits" value="11"/>
>      <param name="dialplan" value="XML"/>
>      <param name="context" value="default"/>
>      <!-- regex to stop dialing when it matches -->
>      <!--<param name="dial-regex" value="5555"/>-->
>      <!-- regex to stop dialing when it does not match -->
>      <!--<param name="fail-dial-regex" value="^5"/>-->
>    </span>
>    <span id="2">
>      <!--<param name="hold-music" value="$${moh_uri}"/>-->
>      <!--<param name="enable-analog-option" value="call-swap"/>-->
>      <!--<param name="enable-analog-option" value="3-way"/>-->
>      <param name="tonegroup" value="us"/>
>      <param name="digit-timeout" value="2000"/>
>      <param name="max-digits" value="11"/>
>      <param name="dialplan" value="XML"/>
>      <param name="context" value="default"/>
>      <!-- regex to stop dialing when it matches -->
>      <!--<param name="dial-regex" value="5555"/>-->
>      <!-- regex to stop dialing when it does not match -->
>      <!--<param name="fail-dial-regex" value="^5"/>-->
>    </span>
>  </analog_spans>
>
> </configuration>
>
> % cat /etc/openzap/openzap.conf
> [span wanpipe]
> trunk_type => t1
> b-channel => 1:1-23
> d-channel=> 1:24
>
> [span wanpipe]
> trunk_type => t1
> b-channel => 2:25-47
> d-channel=> 2:48
>
> % cat /etc/openzap/wanpipe.conf
> [defaults]
> codec_ms => 20
> wink_ms => 150
> flash_ms => 750
>
> % cat /etc/wanpipe/wanpipe1.conf
> #================================================
> # WANPIPE1 Configuration File
> #================================================
> #
> # Date: Tue Dec 12 16:21:45 UTC 2006
> #
> # Note: This file was generated automatically
> #       by /usr/sbin/wancfg program.
> #
> #       If you want to edit this file, it is
> #       recommended that you use wancfg program
> #       to do so.
> #================================================
> # Sangoma Technologies Inc.
> #================================================
>
> [devices]
> wanpipe1 = WAN_AFT, Comment
>
> [interfaces]
> w1g1 = wanpipe1, , TDM_VOICE, Comment
>
> [wanpipe1]
> CARD_TYPE       = AFT
> S514CPU         = A
> CommPort        = PRI
> AUTO_PCISLOT    = NO
> PCISLOT         = 1
> PCIBUS          = 2
> FE_MEDIA        = T1
> FE_LCODE        = B8ZS
> FE_FRAME        = ESF
> FE_LINE         = 1
> TE_CLOCK        = NORMAL
> TE_REF_CLOCK    = 0
> TE_SIG_MODE     = CCS
> TE_HIGHIMPEDANCE        = NO
> LBO             = 0DB
> FE_TXTRISTATE   = NO
> MTU             = 1500
> UDPPORT         = 9000
> TTL             = 255
> IGNORE_FRONT_END = NO
> TDMV_SPAN       = 1
> TDMV_DCHAN      = 24
>
> [w1g1]
> ACTIVE_CH       = ALL
> TDMV_ECHO_OFF   = NO
> TDMV_HWEC       = NO
>
> % cat /etc/wanpipe/wanpipe2.conf
> #================================================
> # WANPIPE1 Configuration File
> #================================================
> #
> # Date: Tue Dec 12 16:21:45 UTC 2006
> #
> # Note: This file was generated automatically
> #       by /usr/sbin/wancfg program.
> #
> #       If you want to edit this file, it is
> #       recommended that you use wancfg program
> #       to do so.
> #================================================
> # Sangoma Technologies Inc.
> #================================================
>
> [devices]
> wanpipe2 = WAN_AFT, Comment
>
> [interfaces]
> w2g1 = wanpipe2, , TDM_VOICE, Comment
>
> [wanpipe2]
> CARD_TYPE       = AFT
> S514CPU         = B
> CommPort        = PRI
> AUTO_PCISLOT    = NO
> PCISLOT         = 1
> PCIBUS          = 2
> FE_MEDIA        = T1
> FE_LCODE        = B8ZS
> FE_FRAME        = ESF
> FE_LINE         = 1
> TE_CLOCK        = NORMAL
> TE_REF_CLOCK    = 0
> TE_SIG_MODE     = CCS
> TE_HIGHIMPEDANCE        = NO
> LBO             = 0DB
> FE_TXTRISTATE   = NO
> MTU             = 1500
> UDPPORT         = 9000
> TTL             = 255
> IGNORE_FRONT_END = NO
> TDMV_SPAN       = 2
> TDMV_DCHAN      = 24
>
> [w2g1]
> ACTIVE_CH       = ALL
> TDMV_ECHO_OFF   = NO
> TDMV_HWEC       = NO
>
> freeswitch at hostname-elided> load mod_openzap
> 2008-12-11 16:23:08 [ERR] zap_wanpipe.c:414 wp_open_range() failure 
> configuring device s1c1
> 2008-12-11 16:23:08 [ERR] zap_wanpipe.c:414 wp_open_range() failure 
> configuring device s1c2
> 2008-12-11 16:23:08 [ERR] zap_wanpipe.c:414 wp_open_range() failure 
> configuring device s1c3
> 2008-12-11 16:23:08 [ERR] zap_wanpipe.c:414 wp_open_range() failure 
> configuring device s1c4
> 2008-12-11 16:23:08 [ERR] zap_wanpipe.c:414 wp_open_range() failure 
> configuring device s1c5
> 2008-12-11 16:23:08 [ERR] zap_wanpipe.c:414 wp_open_range() failure 
> configuring device s1c6
> 2008-12-11 16:23:08 [ERR] zap_wanpipe.c:414 wp_open_range() failure 
> configuring device s1c7
> 2008-12-11 16:23:08 [ERR] zap_wanpipe.c:414 wp_open_range() failure 
> configuring device s1c8
> 2008-12-11 16:23:08 [ERR] zap_wanpipe.c:414 wp_open_range() failure 
> configuring device s1c9
> 2008-12-11 16:23:08 [ERR] zap_wanpipe.c:414 wp_open_range() failure 
> configuring device s1c10
> 2008-12-11 16:23:08 [ERR] zap_wanpipe.c:414 wp_open_range() failure 
> configuring device s1c11
> 2008-12-11 16:23:08 [ERR] zap_wanpipe.c:414 wp_open_range() failure 
> configuring device s1c12
> 2008-12-11 16:23:08 [ERR] zap_wanpipe.c:414 wp_open_range() failure 
> configuring device s1c13
> 2008-12-11 16:23:08 [ERR] zap_wanpipe.c:414 wp_open_range() failure 
> configuring device s1c14
> 2008-12-11 16:23:08 [ERR] zap_wanpipe.c:414 wp_open_range() failure 
> configuring device s1c15
> 2008-12-11 16:23:08 [ERR] zap_wanpipe.c:414 wp_open_range() failure 
> configuring device s1c16
> 2008-12-11 16:23:08 [ERR] zap_wanpipe.c:414 wp_open_range() failure 
> configuring device s1c17
> 2008-12-11 16:23:08 [ERR] zap_wanpipe.c:414 wp_open_range() failure 
> configuring device s1c18
> 2008-12-11 16:23:08 [ERR] zap_wanpipe.c:414 wp_open_range() failure 
> configuring device s1c19
> 2008-12-11 16:23:08 [ERR] zap_wanpipe.c:414 wp_open_range() failure 
> configuring device s1c20
> 2008-12-11 16:23:08 [ERR] zap_wanpipe.c:414 wp_open_range() failure 
> configuring device s1c21
> 2008-12-11 16:23:08 [ERR] zap_wanpipe.c:414 wp_open_range() failure 
> configuring device s1c22
> 2008-12-11 16:23:08 [ERR] zap_wanpipe.c:414 wp_open_range() failure 
> configuring device s1c23
> 2008-12-11 16:23:08 [ERR] zap_wanpipe.c:414 wp_open_range() failure 
> configuring device s1c24
> 2008-12-11 16:23:08 [ERR] zap_wanpipe.c:414 wp_open_range() failure 
> configuring device s2c25
> 2008-12-11 16:23:08 [ERR] zap_wanpipe.c:414 wp_open_range() failure 
> configuring device s2c26
> 2008-12-11 16:23:08 [ERR] zap_wanpipe.c:414 wp_open_range() failure 
> configuring device s2c27
> 2008-12-11 16:23:08 [ERR] zap_wanpipe.c:414 wp_open_range() failure 
> configuring device s2c28
> 2008-12-11 16:23:08 [ERR] zap_wanpipe.c:414 wp_open_range() failure 
> configuring device s2c29
> 2008-12-11 16:23:08 [ERR] zap_wanpipe.c:414 wp_open_range() failure 
> configuring device s2c30
> 2008-12-11 16:23:08 [ERR] zap_wanpipe.c:414 wp_open_range() failure 
> configuring device s2c31
> 2008-12-11 16:23:08 [ERR] zap_wanpipe.c:414 wp_open_range() failure 
> configuring device s2c32
> 2008-12-11 16:23:08 [ERR] zap_wanpipe.c:414 wp_open_range() failure 
> configuring device s2c33
> 2008-12-11 16:23:08 [ERR] zap_wanpipe.c:414 wp_open_range() failure 
> configuring device s2c34
> 2008-12-11 16:23:08 [ERR] zap_wanpipe.c:414 wp_open_range() failure 
> configuring device s2c35
> 2008-12-11 16:23:08 [ERR] zap_wanpipe.c:414 wp_open_range() failure 
> configuring device s2c36
> 2008-12-11 16:23:08 [ERR] zap_wanpipe.c:414 wp_open_range() failure 
> configuring device s2c37
> 2008-12-11 16:23:08 [ERR] zap_wanpipe.c:414 wp_open_range() failure 
> configuring device s2c38
> 2008-12-11 16:23:08 [ERR] zap_wanpipe.c:414 wp_open_range() failure 
> configuring device s2c39
> 2008-12-11 16:23:08 [ERR] zap_wanpipe.c:414 wp_open_range() failure 
> configuring device s2c40
> 2008-12-11 16:23:08 [ERR] zap_wanpipe.c:414 wp_open_range() failure 
> configuring device s2c41
> 2008-12-11 16:23:08 [ERR] zap_wanpipe.c:414 wp_open_range() failure 
> configuring device s2c42
> 2008-12-11 16:23:08 [ERR] zap_wanpipe.c:414 wp_open_range() failure 
> configuring device s2c43
> 2008-12-11 16:23:08 [ERR] zap_wanpipe.c:414 wp_open_range() failure 
> configuring device s2c44
> 2008-12-11 16:23:08 [ERR] zap_wanpipe.c:414 wp_open_range() failure 
> configuring device s2c45
> 2008-12-11 16:23:08 [ERR] zap_wanpipe.c:414 wp_open_range() failure 
> configuring device s2c46
> 2008-12-11 16:23:08 [ERR] zap_wanpipe.c:414 wp_open_range() failure 
> configuring device s2c47
> 2008-12-11 16:23:08 [ERR] zap_wanpipe.c:414 wp_open_range() failure 
> configuring device s2c48
> 2008-12-11 16:23:08 [INFO] zap_io.c:2068 load_config() Configured 0 
> channel(s)
> 2008-12-11 16:23:08 [ERR] zap_io.c:2161 zap_global_init() No modules 
> configured!
> 2008-12-11 16:23:08 [ERR] mod_openzap.c:1861 mod_openzap_load() Error 
> loading OpenZAP
> 2008-12-11 16:23:08 [CRIT] switch_loadable_module.c:756 
> switch_loadable_module_load_file() Error Loading module 
> /usr/local/freeswitch/mod/mod_openzap.so
> **Module load routine returned an error**
>
>
>
>
> _______________________________________________
> Freeswitch-users mailing list
> Freeswitch-users at lists.freeswitch.org
> http://lists.freeswitch.org/mailman/listinfo/freeswitch-users
> UNSUBSCRIBE:http://lists.freeswitch.org/mailman/options/freeswitch-users
> http://www.freeswitch.org

More information about the FreeSWITCH-users mailing list